Difference between revisions of "ConfigNetwork"
| (7 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
{{DISPLAYTITLE:Network}} | {{DISPLAYTITLE:Network}} | ||
| − | [[Category: | + | [[Category:HamsterV6]] |
| + | [[Category:HamsterV5]] | ||
| + | [[Category:HamsterV4]] | ||
| + | [[Category:HamsterV7]] | ||
=== Network === | === Network === | ||
In case you are not using a preconfigured router, the following describes the router needed configuration. | In case you are not using a preconfigured router, the following describes the router needed configuration. | ||
| − | == Hamster Network topology == | + | == Hamster Network topology == |
| + | |||
| + | <syntaxhighlight lang="bash" line='line'> | ||
Name: hamster_net | Name: hamster_net | ||
Security: WPA2 personal | Security: WPA2 personal | ||
| Line 12: | Line 17: | ||
Netmask: 255.255.255.0 | Netmask: 255.255.255.0 | ||
Router's IP: 10.0.2.138 | Router's IP: 10.0.2.138 | ||
| − | + | </syntaxhighlight> | |
| − | + | ||
| − | Go to Advanced Routing → Static Routing List → Add... | + | == Router configuration, 2nd PI == |
| − | For each robot (numbered <n>), add the corresponding entry: | + | In order to reach the slave raspberry pi on each Hamster, configure the routing table as following: |
| − | + | ||
| + | * Go to Advanced Routing → Static Routing List → Add... | ||
| + | * For each robot (numbered <n>), add the corresponding entry: | ||
| + | |||
| + | <syntaxhighlight lang="bash" line='line'> | ||
Destination IP: 192.168.<n>.0 | Destination IP: 192.168.<n>.0 | ||
Subnet Mask: 255.255.255.0 | Subnet Mask: 255.255.255.0 | ||
Default gateway: 10.0.2.<n> | Default gateway: 10.0.2.<n> | ||
| + | </syntaxhighlight> | ||
| − | + | == Configuring the Hamsters' IP == | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | ==Configuring the Hamsters' IP== | ||
Hamster robots arrive with a pre-configured specific IP’s. Unless you know what you are doing, this should not be changed. | Hamster robots arrive with a pre-configured specific IP’s. Unless you know what you are doing, this should not be changed. | ||
Robot 1 configuration: | Robot 1 configuration: | ||
| − | Master raspberry pi IP: 10.0.2.1 or 192.168.1.1 | + | * Master raspberry pi IP: 10.0.2.1 or 192.168.1.1 |
| − | Slave raspberry pi IP: 192.168.1.2 | + | * Slave raspberry pi IP: 192.168.1.2 |
Robot 2 configuration: | Robot 2 configuration: | ||
| − | Master raspberry pi IP: 10.0.2.2 or 192.168.2.1 | + | * Master raspberry pi IP: 10.0.2.2 or 192.168.2.1 |
| − | Slave raspberry pi IP: 192.168.2.2 | + | * Slave raspberry pi IP: 192.168.2.2 |
The Hamster's connection configurations can be changed in the /etc/network/interfaces , and /wpa_supplicant/wpa_supplicant.conf . | The Hamster's connection configurations can be changed in the /etc/network/interfaces , and /wpa_supplicant/wpa_supplicant.conf . | ||
SSH connection details: | SSH connection details: | ||
| + | <syntaxhighlight lang="bash" line='line'> | ||
Username: pi | Username: pi | ||
Password: hamster | Password: hamster | ||
| + | </syntaxhighlight> | ||
Latest revision as of 07:27, 2 July 2020
Contents
Network
In case you are not using a preconfigured router, the following describes the router needed configuration.
Hamster Network topology
<syntaxhighlight lang="bash" line='line'> Name: hamster_net Security: WPA2 personal Password: hamsterHAMSTER
Netmask: 255.255.255.0 Router's IP: 10.0.2.138 </syntaxhighlight>
Router configuration, 2nd PI
In order to reach the slave raspberry pi on each Hamster, configure the routing table as following:
- Go to Advanced Routing → Static Routing List → Add...
- For each robot (numbered <n>), add the corresponding entry:
<syntaxhighlight lang="bash" line='line'> Destination IP: 192.168.<n>.0 Subnet Mask: 255.255.255.0 Default gateway: 10.0.2.<n> </syntaxhighlight>
Configuring the Hamsters' IP
Hamster robots arrive with a pre-configured specific IP’s. Unless you know what you are doing, this should not be changed.
Robot 1 configuration:
- Master raspberry pi IP: 10.0.2.1 or 192.168.1.1
- Slave raspberry pi IP: 192.168.1.2
Robot 2 configuration:
- Master raspberry pi IP: 10.0.2.2 or 192.168.2.1
- Slave raspberry pi IP: 192.168.2.2
The Hamster's connection configurations can be changed in the /etc/network/interfaces , and /wpa_supplicant/wpa_supplicant.conf .
SSH connection details: <syntaxhighlight lang="bash" line='line'> Username: pi Password: hamster </syntaxhighlight>
